|
Support Mercedes-Benz All Key Lost
Xtool X100 PAD3 Features
1.New keys programming
2. PIN Code reading with EEPROM
3.Hexadcimal editor(Win Hex)
4.Reads keys from immobilizer's memory
5.New immobilizer programming
6.Vehicle Identification Number programming
7.Reset ECM & reset immobilizer
8.New remote controller programming
9.With full and strong database for the most important vehicle makes
X100 PAD3 Functions
* Key programming
* Oil Reset/Engine oil light reset
* Odometer Adjustment
* Tire Pressure Warning Light Reset (Manual Operation)
* Timing belt light reset (Manual Operation)
* EPB Electrical Parking Brake Adaptation
* TPS Throttle Body Adaptation
* Steering Angle Calibration
* Battery Reset
* PIN Code Reading
* Hexadcimal editor(Win Hex)
* OBDII Diagnosis
* INJ Code
* Support the latest vehicles with CAN BUS and UDS protocol
Key Programming Vehicle Coverage:
Asia: for Toyota,for Lexus, for Honda, forAcura,for Mazda,forNissan,
for Infiniti, for Mitsubishi, for Subaru, for Suzuki, for Kia, for
Hyundai, for Daewoo, for SSANGYONG, for Proton, etc
Europe: for Audi, for VW, for Skoda, for Seat, for Porsche, for Opel,
for Citroen, for Peugeot, for Jaguar, for Land Rover, for Lincoln, for
Renault, etc
With KC100
Support for Volkswagen for Audi for Skoda 4th&5th generation all key lost, MQB key matching
Support for Volkswagen for Audi for Skoda 4th generation 96-bit online, 5th generation online, MQB online key matching
Support for BMW CAS1-CAS3++ CAS4/CAS4+ key matching
Support for Land Rover's smart key write start function after 2015
Support for Fiat, for Fischer, 500, for Palio and other models
Support for Toyota for Lexus all lost and disassembly-free, can realize
94, 98, 88, A8, A9, 39 simulation key generation(Need to buy Xtool KS-1)
Some car models require that you have pin code before key programming
KC501 Key & Chip PROGRAMMER:
KC501 is a professional Key & chip programmer which can not only
read,write keys and read key remote frequency, but also generate dealer
keys. It support read and write MCU/EEPROM chips, reach and write
Mercedes Infrared keys. Moreover, it support PC connection which brings
you better user experience.
1. Support registers, microcontrollers, key programming and other types of chips read/write, anticipate and other functions;
2. Support key automatic identification, partial key reading, key
generation, key reading information, key check, key unlock and other
functions;
3. Can be put in use with tablets for immobilization.
4. EZS for Mercedes Key Programming
5. Car Key Remote Control Frequency Test
6. EEPROM Read&Write Chip
7. MCU Read&Write
8. ECU Programming Clone
XTOOL M821 Adapter
XTOOL M821 Mercedes-Benz All Keys Lost Communication Adapter is used for
finishing and optimizing all key lost programming for multiple
Mercedes-Benz modules.With M821 Adapter, you can save as much as 65% of
the calculation time on the process, or save you from plugging the key
emulator in and out for hundreds of times.
XTOOL M821 Adapter Feature:
1. OBD-16 port: Used to connect to J1Z02_BENZ communication cable or connect to EIS/EZS modules via DuPont cables.
Caution: Don't connect to the OBD port on the car directly.
2. Status Light: Shows the power status of the adapter. When the red lights are on, that indicates the power is on.
3. Comm Light: Shows the communication status of the adapter. When the
blue lights are on, that indicates the adapter is communicating with the
tablet.
4. DB15 port: Used to connect to the main cable of XTOOL tablets.
Note: Before connected to M821 Adapter, please disconnect the OBD2-16 connector from the main cable.
XTOOL M821 Adapter Support EIS Modules
W164(OLD) W166 W204 W212(NEW)
W164(NEW) W216 W221 W211
Package List:
1 set x X100 PAD3
1 set x KC501
1 set x M821 Adapter
|
